PKB30W-1050-55-TN - 30 watt constant current programmable led driver, 120 & 277V Input, 275-1050mA current output, max power 30 watts, class 2, 0/10V dimming protocol.
FEATURES
• UL Class P
• Class 2 output
• Lifetime: 5 years @ Tc ≤ 75°C
• 90℃ maximum case hot spot temperature
• Surge protection:
• IEC61000-4-5: 2 kV line to line/2 kV line to earth
• 2.5 kV ring wave: ANSI/IEEE c62.41.1-2002 & c62.41.2-2002
category A
• Complies with ENERGY STAR®, DLC (DesignLight Consortium®), and CA Title 24 technical requirements
PROGRAMMING
• Audio jack programming
• Current: see page 2 for current range
• 0-10V dimming profiles: Linear, Non-linear, Logarithmic
• Data log read: SKU, S/N, lot code, hours of operation, FW rev., power cycles
APPLICATIONS
• Commercial & residential lighting
• Architectural lighting
• Indoor Lighting
6 -ENVIRONMENTAL CONDITIONS
Units Minimum Typical Maximum Notes
Operating Ambient Temperature50°C is the non-derated temperature (Refer to section 9°C -20 50(Ta) "Output power de-rating at higher temperatures".
Case temperature measured at the hot spot tc (see label Maximum Case Temperature (Tc) °C +90 in page 15)
Storage Temperature °C -40 +85
Humidity % 5 -95 Non-condensing
Cooling Convection cooled
Acoustic Noise dBA 24 Measured at a distance of 1 foot, without dimmer
Mechanical Shock Protection per EN60068-2-27
Vibration Protection per EN60068-2-6 & EN60068-2-64
MTBF > 200,000 hours when operated at nominal input and output conditions, and at Tc ≤ 75°C
Lifetime 50,000 hours at Tc ≤ 75°C maximum case hot spot temperature (see hot spot tc on label in page 15)
5 years. Users must utilize proper thermal management techniques to ensure proper thermal conductivity Warranty between the driver and heat sink. The use of double-sided tape to mount the driver voids the warranty.
7 -EMC COMPLIANCE AND SAFETY APPROVALS
EMC Compliance
Conducted and Compliant with FCC CFR Title 47 Part 15 Class A at 120 & 277 Vac Radiated EMI
Harmonic Current Emissions IEC61000-3-2 For Class C equipment
Voltage Fluctuations & Flicker IEC61000-3-3
ESD (ElectrostaticIEC61000-4-2 6 kV contact discharge, 8 kV air discharge, level 3 Discharge)
RF Electromagnetic FieldIEC61000-4-3 3 V/m, 80 -1000 MHz, 80% modulated at a distance of 3 meters Susceptibility
Immunity Electrical Fast Transient IEC61000-4-4 ± 2 kV on AC power port for 1 minute, ±1 kV on signal/control lines
Compliance IEC61000-4-5 ± 2 kV line to line (differential mode) /± 2 kV line to common mode ground Surge ANSI/IEEE c62.41.1-2002 & c62.41.2-2002 category A, 2.5 kV ring wave
Conducted RF IEC61000-4-6 3V, 0.15-80 MHz, 80% modulated Disturbances
Voltage Dips IEC61000-4-11 >95% dip, 0.5 period; 30% dip, 25 periods; 95% reduction, 250 periods
Safety Agency Approvals
UL UL8750 listed Class 2, supplement SF
cUL CAN/CSA C22.2 No. 250.13-14 LED equipment for lighting applications
NOM
Safety
Units Minimum Typical Maximum Notes
Hi Pot (High Potential) or Vdc 2200 Tested at the RMS voltage equivalent of 1555 Vac Dielectric voltage-withstand